1. When the light switch is rotated to the position, the whole car lights turn on.

A. Right

B. Wrong

Answer：B

2. What is this manipulation device?

A. switch of reverse light

B. switch of wiper

C. switch of the hazard lights

D. combination switch of lights and signals

Answer：D

3. Whats the meaning of this sign?

A. stop to yield

B. one-way road

C. going first when crossing each other

D. the opposite vehicle goes first when crossing each other

Answer：C

4. When driving at night, the driver should try as much as possible to avoid overtaking. When he really needs to overtake, he may switch the high and low beam lights to alert the vehicle in front.

A. Right

B. Wrong

Answer：A

5. When driving at night, the driver should go at a lower speed because his field of vision is limited and he can hardly observe the traffic conditions beyond the area covered by his vehicle light.

A. Right

B. Wrong

Answer：A

6. When the traffic conditions at an intersection are complicated, the driver should be patiently waiting instead of taking chance.

A. Right

B. Wrong

Answer：A

7. This sign indicates indoor car park here.

A. Right

B. Wrong

Answer：A

8. The contents of subject 2 test for small motor vehicle include Reversing stall parking, stopping at the appointed position and setting off on a slope, pulling over, driving by S-shaped line, sharp turning.

A. Right

B. Wrong

Answer：A

9. Whats the meaning of this sign?

A. no going straight and no changing to left lane

B. no going straight and no left turn

C. allowed to go straight and change to left lane

D. no going straight and no right turn

Answer：D

10. Traffic lights are divided into red, green and yellow light.

A. Right

B. Wrong

Answer：A

11. The cycle for recording the accumulated penalty points for violating road traffic regulations is ____________.

A. 14 months

B. 12 months

C. 6 months

D. 10 months

Answer：B

12. How to use lights when overtaking at night?

A. turn off the high beam light

B. turn on high beam lights

C. use fog lights

D. using the high and low beam lights alternately

Answer：D

13. It lights to remind that the driver‘s seat is not adjusted properly.

A. Right

B. Wrong

Answer：B

14. Traffic signals include Traffic lights, Traffic signs and Command of the traffic police.

A. Right

B. Wrong

Answer：A

15. How to pass when encountering this situation at the intersection?

A. make sure it is safe to pass

B. turn right and speed up to pass

C. speed up and pass straight

D. turn left and speed up to pass

Answer：A

16. Which lane to choose when turning left in this intersection?

A. the far left lane

B. middle lane

C. not need to change lane

D. the far right lane

Answer：A

17. Before entering a level crossing, the vehicle should reduce speed and change to a lower gear, and _____ after entering the level crossing.

A. Cannot change gear

B. Can change gear

C. Can change to a higher gear

D. Stop and look

Answer：A

18. When braking on a muddy road, the tires can easily spin or drift and cause traffic accidents.

A. Right

B. Wrong

Answer：A

19. Whats the role of indicative sign?

A. tell the direction information

B. warn danger ahead

C. restrict the vehicles and pedestrians from passing

D. indicate the vehicles and pedestrians to go ahead

Answer：D

20. It lights to indicate that ______

A. not buckled up

B. safety belt malfunction

C. the safety belts are too loose

D. buckled up already

Answer：A

21. When driving at night, the driver should reduce speed and go forward if the vehicle coming in the opposite direction fails to turn off the high beam light. This is designed to prevent an accident from happening when there are pedestrians crossing the place where the lights of the two vehicles meet.

A. Right

B. Wrong

Answer：A

22. It displays that oil in tank has less than the warning line

A. Right

B. Wrong

Answer：A

23. Whats the meaning of this sign?

A. water channel

B. bridge

C. tunnel

D. Culvert

Answer：C

24. Whats the role of the indicative marking?

A. No passing

B. indicate vehicles to pass

C. restrict from passing

D. warn and remind

Answer：B

25. When a vehicle changes lane before an intersection, the driver should do so ______.

A. In the area marked by solid lines before the intersection

B. In the area marked by solid lines in the intersection

C. In the area marked by broken lines as indicated by the guide arrow

D. Before the stop line at the intersection

Answer：C